EasyScape Gravel Hold

5 Litres

EasyScape Gravel Hold is a multipurpose binder that fixes pebbles, gravel, stone, bark & mulch in place.

• Glues new or existing loose garden pebbles, gravel, stone, bark, rubber & mulch*
• Resin binder coats stones in a protective sheen, leaving the surface permeable for water to go through
• EASY to use - pour on, spray on, or mix in
• Ready-to-use out of the container
• Water-based resin and non-hazardous
• Professional grade
• Covers up to 12m²

EasyScape Gravel Hold is suitable for pebbles, gravel, stone, bark & mulch, sizes 4mm to 20mm in diameter.

NOTE: This product is NOT designed to withstand excessive or prolonged foot traffic. Performance depends on gravel shape & size, depth of gravel and ground conditions. It is NOT suitable for use by vehicles.

APPLICATION - Use neat, as supplied
- Shake well
- Always test a small hidden area before full use, to ensure compatability and that the finished result is acceptable
- Pebbles and gravel must be washed to remove any dust and allowed to dry before applying EasyScape Gravel Hold

Gravel-Mix Method
In a container or bucket, mix EasyScape Gravel Hold with your gravel until evenly coated, at a ratio of 1L Gravel Hold to 10kg stone. Spread to the desired thickness, and tamp to settle the gravel in place. This mixing method leaves the strongest finish, especially if the surface is to receive any light foot traffic. For best results, allow to dry, then apply a light coating to the gravel using a garden sprayer. Repeat this process if some stones are still loose.

Gravel & Mulch Spray-On Method
EasyScape Gravel Hold can be applied using a garden sprayer. Using a sprayer, apply a generous, even coat across the surface, at a rate of 1m² per litre. Lightly rake and spray again. Leave to dry. Repeat after 24 hours for extra strength.

Gravel & Mulch Pour-On Method
EasyScape Gravel Hold can be poured from a watering can, ensuring your stones or mulch are evenly coated. This method can be useful for smaller areas of gravel or mulch. Make sure you use a watering can with a steady flow that disperses the liquid evenly across the stones or mulch. The surface should be lightly raked and turned over for best results.

NOTE: EasyScape Gravel Hold is air-drying, so application of excessive amounts of the product will leave the surface wet and unbonded for a longer period of time. Drying time is approximately 24 hours - longer in colder weather.

STORAGE
Product should be stored in original container out of direct sunlight. Unopened shelf-life is 12 months from date of manufacture.

IMPORTANT / PRECAUTIONS
- Keep children and pets away until the surface is completely dry and the stones or mulch have stabilised.
- Do not apply in direct sunlight, damp/wet conditions, or if rain is expected within 72 hours of application.
- Do not apply in frosty conditions, or when the temperature will be below 5 C.
- Avoid direct contact with shrubs, grass, and plants.
- Not suitable for areas used by vehicles or frequent foot traffic.

HEALTH & SAFETY
- Keep out of reach of children.
- Do not get in eyes, on skin, or on clothing.
- Wear eye/face protection, protective gloves and clothing.

If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists, seek medical advice/attention.

If on skin: Wash with plenty of soap and water. If skin irritation or rash occurs, seek medical advice/attention.

May produce an allergic reaction.

Made in the UK.

DISCLAIMER
If used in accordance with the instructions, EasyScape Gravel Hold should produce the results described, but no guarantees are given or implied. Neither the manufacturer nor supplier accept any liability for marking or changes in appearance of the material on which it is used.

* Pebbles, gravel, stone, bark & mulch must be dust free, clean and dry